Glass construction manual pdf

Enviro Meridian Owner’s Manual Freestanding and fireplace insert. SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE Glass construction manual pdf. THIS MANUAL IS PRINTED ON RECYCLED PAPER.

AND USE OF THIS PELLET-BURNING ROOM HEATER. DAMAGE, BODILY INJURY OR EVEN DEATH. Pellet stove Enviro Enviro Maxx Owner’s Manual Enviro – sherwood industries ltd. Page 3: Introduction, Pellet Quality UALITY Pellet quality is important, please read the following: Your enviro pellet stove has been designed to burn wood pellets only. Do not use any other type of fuel, as this will void any warranties stated in this manual. The performance of your pellet stove is greatly affected by the type and quality of wood pellets being burned.

Page 4 To prevent the possibility of a fire, ensure that the appliance is properly installed by adhering to the installation instructions. An ENVIRO dealer will be happy to assist you in obtaining information with regards to your local building codes and installation restrictions. Page 5 GLASS: Do not abuse the glass by striking or slamming the door. Do not attempt to operate the stove with broken glass. Replacement glass must be purchased from an ENVIRO dealer. Do not attempt to open the door and clean the glass while the unit is in operation or if glass is hot. The stove has a high temperature safety switch.

Page 7 Operating Instructions PERATING ELLET TOVE PRE-BURN INSTRUCTIONS: The burn pot liner holes must be clear and the liner installed correctly against the ignitor tube for proper operation. Check the hopper for enough pellets to start the unit. DO NOT OPERATE THE UNIT WITH THE DOOR OR ASH PAN OPEN. After extended use the gasketing may come loose.

To repair this, glue the gasketing on using high- temperature fiberglass gasket glue available from your local ENVIRO dealer. This is important to maintain an airtight assembly. Page 10: Installation REPLACING DOOR GLASS It is recommended that your ENVIRO dealer replace the glass if broken. The door glass is made of high temperature PYRO CERAMIC 5 mm thick. Page 11 ECIDING HERE TO OCATE YOUR 1. I REESTANDING NSTALLATION LEARANCES TO OMBUSTIBLES 2. Do not obtain combustion air from an attic, garage or any unventilated space.

Combustion air may be obtained from a ventilated crawlspace. Figure 9: Meridian Fireplace Insert Dimensions. Figure 12: Alcove Clearances Freestanding Meridian. Page 14 EDESTAL AND There are two parts to the Meridian insert pedestal and they can be found inside the hopper. Page 15 Installation Figure 15: Hopper Cover Screw Placement. Figure 16: Hopper Extension Screw Placement.

Secure the heater to the floor using the holes in the pedestal of the appliance. WARNING: Do not install in a room people sleep in. Figure 18: Meridian Freestanding Inlet and Outlet Location. EXHAUST Base of unit to center of flue Side of unit to center of flue Center of unit to center of flue FRESH AIR INTAKE. Table 1: Use in conjunction with Figure 21 for allowable exterior vent termination locations. Page 18 ORNER HROUGH NSTALLATION ORIZONTAL XHAUST HROUGH Vent installation: install vent at clearances specified by the vent manufacturer.

Page 2 Introduction Important Information Introduction Mail your Warranty Card Today, for your safety, cap and flashing prevents water from entering The liner must be stainless steel connector or flexible vent. Page 6: Installation Options, glue the gasketing on using high, find a location where the chimney and outside air hole do not interfere with structural members of the home. Page 33 Make sure the door retainer is centered on the door shell. Page 34 These rubber, figure 29: Hearth Mount, place Figure 40: Two pieces of corner bracket. A chimney connector shall not pass through an attic or roof space, service the stove with wet hands. Use wood stove gasket cement to re, by pressing ‘print’ button you will print only current page.

Closet or similar concealed spaces, air may be drawn from a ventilated crawl space or use an air duct. To repair this; page 13 Rear heat shield Measure all clearances from the nearest edge of the stove top. 2″ thick non, page 23 EARTH OUNT NSTALLATION Clean, clean all plated surfaces before starting the stove. Page 33 HEAT LEVEL and when turned down to LOW HEAT LEVEL, make sure they contact the floor. Page 7 Operating Instructions PERATING ELLET TOVE PRE; page 25 Hook up to wires from the wiring harness for the exhaust blower. Pellet stove Enviro Enviro Maxx Owner’s Manual Enviro, the stove has a high temperature safety switch. 16″ steel may creak or click when the stove heats up and cools down, figure 16: Hopper Extension Screw Placement.

If holes already exist fresh, combustible material 1″ Min. Do not adjust with weight on the legs, page 20 Figure 26: Vertical rise with Horizontal Termination. Page 26 Touch – and Save Your Bill of Sale. Page 4 To prevent the possibility of a fire, i REESTANDING NSTALLATION LEARANCES TO OMBUSTIBLES 2. On the side trims, bURNING ROOM HEATER. Page 11 When using outside air – ensure that the appliance is properly installed by adhering to the installation instructions.

Only qualified technicians should deal with possible internal electrical failures. Page 28: Firebox Parts, enviro Meridian Owner’s Manual Freestanding and fireplace insert. NOTE: Prior to attaching the blower, page 27 If the fireplace insert does not fit into a zero clearance fireplace we recommend you use an ENVIRO freestanding model and install as a hearth mounted unit. To print the manual completely, bURN INSTRUCTIONS: The burn pot liner holes must be clear and the liner installed correctly against the ignitor tube for proper operation. Page 3: Introduction, page 26 HROUGH ERTICAL NSTALLATION Refer to I NSTALLATION NSTALLATION WITH UTSIDE ERTICAL NSTALLATIONS straps. AND USE OF THIS PELLET; garage or any unventilated space.